Continued implementing RAM module

Added VGA test to project

RAM.v

@@ -1,23 +1,47 @@
 module RAM(
-	input wire clk,
-	output wire [10:0] RAM_addr,		// RAM address buffer
-	output wire RAM_A10,
-	output wire [1:0] RAM_bank_sel,	// RAM bank selection
-	inout wire [15:0] RAM_data,		// RAM data bus
-	output wire RAM_clk,					// RAM clock signal
-	output wire RAM_clk_enable,		// RAM enable clock
-	output wire RAM_enable,				// RAM chip enable
-	output wire RAM_strobe_row,		// RAM row strobe
-	output wire RAM_strobe_col,		// RAM column strobe
-	output wire RAM_write_enable,		// RAM data bus write enable
-	input wire read_rq,					// Read request (Internal)
-	input wire write_rq,					// Write request (Internal)
-	output reg [3:0] RAM_state,		// State information (Internal)
-	output wire op_trigger				// Event trigger wire
+	input  wire         clk,
+	output wire [10:0]  RAM_addr,         // RAM address buffer
+	output wire         RAM_A10,          // RAM address/auto-precharge
+	output wire [1:0]   RAM_bank_sel,     // RAM bank selection
+	inout  wire [15:0]  RAM_data,         // RAM data bus
+	output wire         RAM_clk,          // RAM clock signal
+	output wire         RAM_clk_enable,   // RAM enable clock
+	output wire         RAM_enable,       // RAM chip enable
+	output wire         RAM_strobe_row,   // RAM row strobe
+	output wire         RAM_strobe_col,   // RAM column strobe
+	output wire         RAM_write_enable, // RAM data bus write enable
+	input  wire         read_rq,          // Read request (Internal)
+	input  wire         write_rq,         // Write request (Internal)
+	output reg  [3:0]   RAM_state,        // State information (Internal)
+	output wire         op_trigger        // Event trigger wire
 );
 
+reg [2:0] read_init;                     // Whether or not a read operation has been initiated
+reg       trigger_low;                   // If trigger should be pulled low on next clock cycle
+
+assign op_trigger = read_init == 3'b011;
+assign RAM_enable = ~(read_init != 3'b000);
+assign RAM_clk_enable = read_init != 3'b000;
+
+assign RAM_clk = clk;                    // RAM clock tracks processor input clock
+
 always @(posedge clk) begin
-	
+	if(read_init) begin
+		read_init <= read_init + 3'b001;
+		RAM_state <= 4'b0001;              // STATE: read
+	end
+end
+
+always @(posedge read_rq) begin
+	if(!read_init && !write_rq) begin
+		read_init <= 3'b001;
+	end
+end
+
+always @(posedge write_rq) begin
+	if(!read_init && !read_rq) begin
+		//TODO: Implement read
+	end
 end
 
 endmodule

SevenSegment.v

@@ -72,8 +72,7 @@ VGA screen(clk, gfx_rgb, vga_clk, VGA_rgb, VGA_hsync, VGA_vsync);
 ALU core0(.a(alu_a), .b(alu_b), .op(alu_op), .z(alu_out), .o_flags(alu_flags));
 altpll0 pll_gen(clk, pll[0], pll[1], pll[2], pll[3]);
 
-always @(posedge vga_clk)
-	gfx_rgb <= alu_a[2:0];
+always @(posedge vga_clk) gfx_rgb <= alu_a[2:0];
 
 always @(posedge pll[PLL_SELECT]) begin
 	if(!latch && write && next) begin